TYPHOON SILENT 18E
TECHNICAL DATA
| MODEL | TYPHOON SILENT 18E |
| AIR DELIVERY FAD | 300-320 lit/min (18-19,2m3/h) |
| MAX WORKING PRESSURE | 350 bar |
| STAGES | 3 |
| CYLINDERS | 3 |
| CYLINDER ARRANGEMENT | W |
| 1ST STAGE CYLINDER DIAMETER | 80mm |
| 2ND STAGE CYLINDER DIAMETER | 36mm |
| 3RD STAGE CYLINDER DIAMETER | 14mm |
| PISTON STROKE | 60mm |
| SPEED ROTATION | 1290-1380 rpm |
| 1ST STAGE PRESSURE | 5,2 – 5,5 bar |
| 2ND STAGE PRESSURE | 38 – 43 bar |
| TRANSMISSION | V Belt |
| MOTOR POWER | 7,5 kW/ 400V/50Hz
8,5 kW/ 440V/60Hz (Class F, IP 55) |
| OIL CAPACITY | 1.6 lit synthetic compressor oil |
| AIR OUTLET TEMPERATURE | 5 – 8 Co above ambient temperature |
| MAX PERMISSIBLE AMBIENT TEMPERATURE | +50 to +450 C |
| COOLING AIR FLOW MIN REQUIRED APPROXIMATELY | 2700m3/ hr |
| MAX INCLINATION OF COMPRESSOR | 150 |
| NOISE LEVEL | 70 dB |
| DIMENSIONS (L x W x H) | 80 X 98 X 118 cm |
| WEIGHT | 263-269 Kg |
| FILLING TIME OF CYL 10LT @ 225BAR | 7,5 min ± 5% |
| FILLING TIME OF CYL 10LT @300BAR | 10,0 min ± 5% |
STANDARD EQUIPMENT |
| Micronic Air Inlet Filter. |
| Condensate Separator after 2nd Stage. |
| Large Stainless Steel Intercoolers & aftercooler at all stages. |
| Large fan (500mm diam.) for optimum cooling of cylinders, intercoolers & aftercoolers, making the compressor capable for continuous operation. |
| Combined BA Filter D110Χ495 including Coalescing Pre-filter (0,5mg/m3 oil residual) and 1 x (Active Carbon / Molecular Sieve cartridge) D65Χ260 cartridge, with the supply of absolutely clean air exceeding by far the requirements of EN 12021:2014. |
| Pressure maintaining valve & non-return valve allowing for safe, efficient & extended filtration. |
| Two (2) Kevlar* Filling Hoses, 1,2m each, complete with DIN and INTERNATIONAL ‘’A’’ clamp Adaptors and lever operated on/off valves with automatic ventilation.
*Kevlar hoses are manufactured with very strong & resistant material and are pin pricked for air relief in atmosphere in case of damage |
| Safety Valves in all stages. |
| Built-In Vibration Pads. |
| Soundproof insulation ensuring very low noise level. |
| Automatic belt tensioning system. |
| Star / Delta starting system. |
| Condensate collecting tank with level indication. |
| Emergency Stop button. |
| High Temperature Alarm & Shutdown error via Analogue temperature sensor at final stage, for additional safety and accurate indications. |
| Motor thermal overload protection. |
| Interstage pressure manometers |
| Automatic Condensate Drains with manual backups in all stages. |
| Automatic start & stop at the desirable pressure via analogue pressure sensor 400bar |
| 24V secondary voltage providing safety during routine operation. |
| Inter stage (1st, 2nd) pressure sensors providing emergency shutdown in case of overpressure. |
| Main Switch |
| · Digital Controller incorporating:
§ Digital Display. § Start/Stop button. § Reset button. § Menu button. § Easy adjustment of all the parameters of the controller through a menu. § Interstage pressure index & protection in case of overpressure, via a pressure sensor. § Filling (final) pressure adjustment/index & protection in case of overpressure, via a pressure sensor. § Automatic Restart Pressure adjustment/index (when required), via a pressure sensor. § Operating temperature index & protection in case of overheating and wiring faults, via a temperature sensor. |
- Operating hours index.
- Remaining hours for service index
- Warning/Shutdown error for BA cartridge change
- Warning/Shutdown error for oil change.
- Recording of last 15 alarms / trips (malfunctions).
- Remote Start/Stop – Remote Load/Unload function.
- Leakage, Safety valves and condensate drains test.
Remark for service index: The controller warns every 26 operating hours for replacement of the BA cartridge. If the compressor reaches 28 operating hours and the BA cartridge is not replaced yet, it stops automatically and a trip code number appears on the display.
The controller also warns every 990 operating hours for oil change, and if at 1.000 operating hours the oil is not changed yet, the compressor stops automatically and another trip code number appears on the display
Note: Fuse box & Compressor Plug supplied by customer.
OPTIONAL EQUIPMENT |
| Dual pressure filling facility with pressure regulator allowing simultaneous filling of 225 & 330bar |
| Extra filling hose DIN 200 & International or DIN300. *(maximum total hoses = 4pcs). |
| Voltage failure and phase rotation safety device. |
| Extra Combined BA Filter D110x495 including Coalescing Pre-filter (0,5mg/m3 oil residual) and 1 x (Active Carbon / Molecular Sieve cartridge) D65Χ260 cartridges, with the supply of absolutely clean air exceeding by far the requirements of EN 12021:2014. |
| Oil Pump Lubrication System c/w low oil pressure switch Alarm / Shut Down, oil cooler, oil filter & flow regulator. |
| Humidity Control
Filter state control system, PARAMINA HUMIDITY CONTROL, a device with main target to control humidity of high pressure air via: 1. A Central monitoring unit with display, led indicators and menu navigation buttons. 2. A Humidity Sensor incorporated in stainless steel chamber. PARAMINA HUMIDITY CONTROL provides complete information regarding filters’ state (Filter OK – Filter Critical – Change Filter) in terms of humidity, giving the possibility at the same time, to check the reliability of all devices/systems that remove humidity from the air. The use of this device is intended only for this purpose and not for any other use (e.g. cannot replace laboratory humidity measurement devices). Power Supply: 230VAC 50-60Hz or 24VAC 50-60Hz or 24VDC Operating Temperature: +5oC to +45Oc Max. Operating pressure: 420bar Process connection: G1/4 thread § Every 2 years the sensor must be checked and recalibrated or else replaced. In networks with bad air quality, every year. § The humidity sensor is recommended to be installed in between final filter and pressure maintaining valve, vertically as per arrow indication. Power Supply: 230VAC 50-60Hz or 24VAC 50-60Hz or 24VDC Max working Pressure: 420bar |
| 3rd Final stage condensate separator. |
| 3rd Final stage condensate separator in replacement of the BA Filter (industrial use) |
| High Pressure outlet in replacement of filling hoses. |
| Low oil level Sensor / Alarm / Shut down (auto stop). |
| Remote Start / Stop. |
| Special Voltage/Frequency: 230V/50Hz – 230V/60Hz – 3x 230V/60Hz. |
| CO MONITORING & ALARM. |
| CO2 MONITORING & ALARM. |
| H2S MONITORING & ALARM. |
Recommended Spares
- Paramina HPA Oil n.:112755000 (1,6ltr per replacement – replacement every 1.000 working hours and once per year irrespective of the working hours).
- AC/MS Cartridge n.:137000080 (1 pc per replacement-replacement every 28 working hours @20 oC ambient temperature and every six months irrespective of the working hours).
- Coalescing pre-filter cartridge n.:306049631 (1 pc per replacement-replacement every 200 working hours and once a year irrespective of the working hours).
- Air intake cartridge n.:109460302 (1 pc per replacement-replacement every 200 working hours and once a year irrespective of the working hours).
- Oil Pump Filter n.108000682 – when equipped with compressor (1pc per replacement – replacement every 1.000 working hours and once per year irrespective of the working hrs).
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.