TYPHOON CLASSIC 18E TROPICAL
TECHNICAL DATA
| MODEL | TYPHOON CLASSIC 18E Tropical |
| AIR DELIVERY FAD | 320 lit/min (19,2m3/h – 11,3cfm) |
| MAX WORKING PRESSURE | 350 bar |
| STAGES | 3 |
| CYLINDERS | 3 |
| CYLINDER ARRANGEMENT | W |
| 1ST STAGE CYLINDER DIAMETER | 80mm |
| 2ND STAGE CYLINDER DIAMETER | 36mm |
| 3RD STAGE CYLINDER DIAMETER | 14mm |
| PISTON STROKE | 60mm |
| SPEED ROTATION | 1380 rpm |
| 1ST STAGE PRESSURE | 5,2 – 5,5 bar |
| 2ND STAGE PRESSURE | 38 – 43 bar |
| TRANSMISSION | V Belt |
| MOTOR POWER | 9,2kW-12,5Hp / 400V/50Hz or 440V/60Hz
Suitable for 500 C ambient temperature
|
| OIL CAPACITY | 1.6 lit synthetic compressor oil |
| AIR OUTLET TEMPERATURE | 5 – 8 Co above ambient temperature |
| MAX PERMISSIBLE AMBIENT TEMPERATURE | +50 to +500 C |
| COOLING AIR FLOW MIN REQUIRED APPROXIMATELY | 2700m3/ hr |
| MAX INCLINATION OF COMPRESSOR | 150 |
| DIMENSIONS (L x W x H) | 152X 81 X 107 cm |
| WEIGHT | 339 Kg |
| FILLING TIME OF CYL 10LT @ 225BAR | 7,0 min ± 5% |
| FILLING TIME OF CYL 10LT @300BAR | 9,4 min ± 5% |
STANDARD EQUIPMENT |
| Micronic Air Inlet Filter. |
| Condensate Separators after 1st and 2nd Stage. |
| Final – 3rd stage condensate separator. |
Large Stainless Steel Intercoolers & aftercooler at all stages.
|
| Improved heatsink at 2nd stage valve/cylinder head |
| Improved heatsink at final (3rd) stage valve head |
| Improved heatsink at final (3rd) stage cylinder head |
| Large fan (500mm diam.) for optimum cooling of cylinders, intercoolers & aftercoolers, making the compressor capable for continuous operation. |
| Combined BA Filter D110Χ495 420bar max. including Coalescing Pre-filter (0,5mg/m3 oil residual) and 1 x (Active Carbon / Molecular Sieve cartridge) D65Χ260 cartridge, with the supply of absolutely clean air exceeding by far the requirements of EN 12021:2014. |
| Pressure maintaining valve & non-return valve allowing for safe, efficient & extended filtration. |
| Star/Delta starter system. |
| Start/Stop switch. |
| Motor thermal overload protection. |
| 24V secondary voltage providing safety during routine operation. |
| Emergency Stop button. |
| Hourmeter. |
| Automatic stop at the desirable pressure. |
| Automatic Condensate Drains in all stages with manual backups. |
| Condensate collecting tank with level indication. |
| Two (2) Kevlar* Filling Hoses, 1,2m each, complete with DIN300 Adaptors and lever operated on/off valves with automatic ventilation.
*Kevlar hoses are manufactured with very strong & resistant material and are pin pricked for air relief in atmosphere in case of damage. |
| Safety Valves in all stages. |
| Inter stage manometers and Final Stage 400 bar manometer. |
| Built-In Vibration Pads. |
| Automatic belt tensioning system. |
| High temperature alarm & shutdown error via bimetal switch. |
| Low oil level Sensor / Alarm / Shut down (auto stop). |
| Soundproof covers at top, left and right side/Drilled doors at front side. |
| Crane lifting eyebolts |
Note: Fuse box & Compressor Plug supplied by customer.
OPTIONAL EQUIPMENT |
| Dual pressure filling facility with pressure regulator allowing simultaneous filling of 225 & 300bar + Two (2) additional Kevlar* Filling Hoses, 1,2m each, complete with DIN200 & International ‘’A’’ clamp Adaptors and lever operated on/off valves with automatic ventilation (2xDIN300 & 2xDIN200 in total). |
Digital Controller incorporating:
Remark for service index: The controller warns every 26 operating hours for replacement of the BA cartridge. If the compressor reaches 28 operating hours and the BA cartridge is not replaced yet, it stops automatically and a trip code number appears on the display. The controller also warns every 990 operating hours for oil change, and if at 1.000 operating hours the oil is not changed yet, the compressor stops automatically and another trip code number appears on the display.
|
| Voltage failure and phase rotation safety device. |
| Extra Combined BA Filter D110x495 including Coalescing Pre-filter (0,5mg/m3 oil residual) and 1 x (Active Carbon / Molecular Sieve cartridge) D65Χ260 cartridges, with the supply of absolutely clean air exceeding by far the requirements of EN 12021:2014. |
| Star Delta Starting System |
| Oil Pump Lubrication System c/w low oil pressure switch Alarm / Shut Down, oil cooler, oil filter & flow regulator. |
| Humidity Control
Filter state control system, PARAMINA HUMIDITY CONTROL, a device with main target to control humidity of high pressure air via: 1. A Central monitoring unit with display, led indicators and menu navigation buttons. 2. A Humidity Sensor incorporated in stainless steel chamber. PARAMINA HUMIDITY CONTROL provides complete information regarding filters’ state (Filter OK – Filter Critical – Change Filter) in terms of humidity, giving the possibility at the same time, to check the reliability of all devices/systems that remove humidity from the air. The use of this device is intended only for this purpose and not for any other use (e.g. cannot replace laboratory humidity measurement devices). Power Supply: 230VAC 50-60Hz or 24VAC 50-60Hz or 24VDC Operating Temperature: +5oC to +45Oc Max. Operating pressure: 420bar Process connection: G1/4 thread § Every 2 years the sensor must be checked and recalibrated or else replaced. In networks with bad air quality, every year. § The humidity sensor is recommended to be installed in between final filter and pressure maintaining valve, vertically as per arrow indication. Power Supply: 230VAC 50-60Hz or 24VAC 50-60Hz or 24VDC Max working Pressure: 420bar |
| High Pressure outlet in replacement of filling hoses. |
| Automatic start system |
| Remote Start / Stop. |
| Two (2) wheels on the one side of compressor for easy transport. |
| CO MONITORING & ALARM. |
| CO2 MONITORING & ALARM. |
| H2S MONITORING & ALARM. |
Recommended Spares
- Paramina HPA Oil n.:112755000 (1,6ltr per replacement – replacement every 1.000 working hours and once per year irrespective of the working hours).
- Coalescing pre-filter cartridge n.:306049631 (1 pc per replacement-replacement every 200 working hours and once a year irrespective of the working hours).
- Air intake cartridge n.:109460302 (1 pc per replacement-replacement every 200 working hours and once a year irrespective of the working hours).
- Oil Pump Filter n.108000682 – when equipped with compressor (1pc per replacement – replacement every 1.000 working hours and once per year irrespective of the working hrs).
Alternative options of breathing air cartridges
- AC/MS Cartridge n.:137000080 (1 pc per replacement-replacement every 28 working hours @20 oC ambient temperature and every six months irrespective of the working hours)
- AC/MS/HP Cartridge n.:137000100 (1 pc per replacement – every 28 working hours @20 oC ambient temperature and every six months irrespective of the working hours).
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.