Cyclone Classic 24D
TECHNICAL DATA
| MODEL | CYCLONE CLASSIC 24 D |
| AIR DELIVERY FAD | 400 lt/min, 14,13cfm |
| MAX WORKING PRESSURE | 350 bar |
| STAGES | 4 |
| CYLINDERS | 4 |
| CYLINDER ARRANGEMENT | V |
| 1ST STAGE CYLINDER DIAMETER | 105 mm |
| 2ND STAGE CYLINDER DIAMETER | 55 mm |
| 3RD STAGE CYLINDER DIAMETER | 30 mm |
| 4RTH STAGE CYLINDER DIAMETER | 14 mm |
| PISTON STROKE | 89 mm |
| SPEED ROTATION | 700 rpm |
| 1ST STAGE PRESSURE | 2,9 – 3,0 bar |
| 2ND STAGE PRESSURE | 11,5 – 12,0 bar |
| 3RD STAGE PRESSURE | 45,0 – 56,0 bar |
| TRANSMISSION | V BELT |
| MOTOR POWER | 11,2kW Diesel |
| OIL CAPACITY | 2.1 LIT SYNTHETIC COMPRESSOR OIL
(2,3 with oil pump) |
| AIR OUTLET TEMPRERATURE | 50 – 8o C ABOVE AMBIENT TEMPERATURE |
| MAX PERMISSIBLE AMBIENT TEMPERATURE | +50 TO +450 C |
| COOLING AIR FLOW MIN REQUIRED APPROXIMATELY | 2700 m3/ hr |
| MAX INCLINATION OF COMPRESSOR | 150 |
| DIMENSIONS (L x W x H) | 169X 96 X 113 cm |
| WEIGHT | 568 Kg |
| FILLING TIME OF CYL 10LT @ 225BAR | 5,6MIN ± 5% |
| FILLING TIME OF CYL 10LT @300BAR | 7,5 MIN ± 5% |
STANDARD EQUIPMENT |
| Micronic Air Inlet Filter |
| 1,5m air inlet hose with particle strainer. |
| Condensate Separators after 1st, 2nd & 3rd Stage. |
| Final – 4th stage condensate separator. |
| Safety valves in all stages. |
| Combined BA Filter D110Χ728 including Coalescing Pre-filter (0,5mg/m3 oil residual) and 2x (Active Carbon / Molecular Sieve cartridge) D65Χ260 cartridge with hopcalite ( retention of carbon monoxide ), with the supply of absolutely clean air exceeding by far the requirements of EN 12021:2014. |
| Large Stainless Steel Intercoolers – aftercooler at 1st, 2nd, 3rd and 4th stage.
· 3rd stage intercooler extra. · 4th stage aftercooler extra. |
| Large fan (650mm diam.) for optimum cooling of cylinders, intercoolers & aftercoolers, making the compressor capable for continuous operation. |
| Improved heatsink at 3rd stage valve/cylinder head. |
| Improved heatsink at final (4th) stage valve head. |
| Improved heatsink at final (4th) stage cylinder head. |
| High Temperature Alarm & Shutdown error via Bimetal temperature switch at final stage, for additional safety and accurate indications. |
| Automatic Condensate Drains with manual backups in all stages. |
| Automatic stop at the desirable pressure. |
| Pressure maintaining & non-return valve after final BA filter for extended BA filter lifetime. |
| Five (5) Kevlar* Filling Hoses (1.2m each) complete with DIN and INTERNATIONAL ‘’A’’ clamp Adaptors and lever operated on/off valves with automatic ventilation.
*Kevlar hoses are manufactured with very strong & resistant material and are pin pricked for air relief in atmosphere in case of damage. |
| ¼’’ Inter-stage manometers. |
| Built-In Vibration Pads. |
| Condensate collecting tank with level indication. |
| Low oil level Sensor / Alarm / Shut down (auto stop). |
| Electric Starting system with starter. |
| Battery 12VDC. |
| Vibration Hourmeter / Service Timer
Display: · Total running Hours · BA Filter service hours · Oil service hours |
| Interstage / Final stage manometers |
| Automatic belt tensioning system. |
OPTIONAL EQUIPMENT |
| Outlet 1/4” 8S |
| Dual pressure filling facility with pressure regulator allowing simultaneous filling of 225 & 300bar. |
| Oil Pump Lubrication System c/w low oil pressure switch Alarm / Shut Down, oil cooler, oil filter & flow regulator. |
| Filter state control system, PARAMINA HUMIDITY CONTROL, a device with main target to control humidity of high pressure air via:
1. A Central monitoring unit with display, led indicators and menu navigation buttons. 2. A Humidity Sensor incorporated in stainless steel chamber. PARAMINA HUMIDITY CONTROL provides complete information regarding filters’ state (Filter OK – Filter Critical – Change Filter) in terms of humidity, giving the possibility at the same time, to check the reliability of all devices/systems that remove humidity from the air. The use of this device is intended only for this purpose and not for any other use (e.g. cannot replace laboratory humidity measurement devices). Power Supply: 230VAC 50-60Hz or 24VAC 50-60Hz or 24VDC Operating Temperature: +5oC to +45Oc Max. Operating pressure: 420bar Process connection: G1/4 thread § Every 2 years the sensor must be checked and recalibrated or else replaced. In networks with bad air quality, every year. § The humidity sensor is recommended to be installed in between final filter and pressure maintaining valve, vertically as per arrow indication. Power Supply: 230VAC 50-60Hz or 24VAC 50-60Hz or 24VDC Max working Pressure: 420bar |
| Carbon Dioxide (CO2) monitoring / alarm / shutdown system |
| OIL-VOC monitoring / alarm / shutdown system |
| Hydrogen Sulfide (H2S) monitoring / alarm / shutdown system. |
| Carbon Monoxide (Co) monitoring / alarm / shutdown system. |
Recommended Spares All Models:
– Paramina HPA Oil n.:112755000 (2,1ltr per replacement – replacement every 1.000 working hours and once per year irrespective of the working hrs).
– AC/MS/HP Cartridge n.:137000100 (2 pcs per replacement) – replacement every 40 working hours @ 20 oC ambient temperature and every six months irrespective of the working hrs.
– Coalescing pre-filter cartridge n.:306049631 (1 pc per replacement-replacement every 200 working hours and once a year irrespective of the working hrs).
– Air intake cartridge n.:109714601 (1 pc per replacement-replacement every 200 working hours and once a year irrespective of the working hrs).
– Oil Pump Filter n.108000682 – when equipped with compressor (1pc per replacement – replacement every 1.000 working hours and once per year irrespective of the working hrs).
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.